Manual Muscle Testing Arm. 15x treadmill. G has many functions as a treatment modalityas part of a rehab program requirements, Proceedings of an.

• 1216 Answers SOURCE: surely there is some problem in the belt. One of the ways to extend the life of your treadmill is to keep it clean and dust-free. Dirt and dust build-up, especially between the belt and the deck of your treadmill can cause excessive belt-deck friction. This in turn, can damage your electronics and even your motor. You can check for excessive belt-deck friction by setting your treadmill around 4 MPH and walking on it. Press the stop button (or pull the emergency stop switch). You should have to take a few steps before the belt stops - if it stops suddenly there is probably a high friction problem.

Excessive belt-deck friction can also cause motor to stall or sound labored so again, keep your belt and deck free from dust and dirct and look out if this is a problem Posted on Jan 26, 2011. It sounds like the speed sensor is not close enough to the magnet, or the speed sensor is bad. It is located inside the motor area, next to the pulley on the front roller. Well depending on what treadmill you have. It can be shaped like a pencil but shorter. Make sure it is about a centimeter away from the magnet that ison the flywheel.

Once you have moved it turn on the treadmill and try it, if it doesnt work then move the belt with your foot and every time the magnet goes past the sensor you should see a light flicker on the control board if not then the sensor needs to be replaced. Sep 16, 2010 . Astroart 5 Full Version here. Unplug unit remove motor shroud then start calibration procedure.

Royksopp What Else Is There Midi File Free Download Programs. Press the Stop and the Speed Up keys down while inserting the safety key. If you cannot get into calibration then upper console needs to be replaced. Press the Stop key one time. The Time window should read EP:2P.

Some newer models may also say FP, Pass, or the like. This means that it passes the EPROM test. At this point if it show 2F FF or Fail then upper console needs to be replaced. Press either incline key and the incline will calibrate automatically BE CAREFUL, THE TREADMILL WILL RUN AT FULL SPEED IN THIS NEXT MODE! DO NOT STAND ON WALKING BELT. Press the Speed Up key and hold it down until 85 is shown in the Distance window (some models may show the 85 number in another window). If the top speed of the treadmill does not match the displayed speed on the computer console, adjust the max speed potentiometer (pot) on the motor control board.

This is the board that the red and black motor wires connect directly into in the motor area. The Max Speed pot is clearly labeled. The max speed potentiometer is a small square with a mobile center and is located in one corner of the board and is labeled MAX SPD. It is near the harness that carries the speed signal labeled H,W,L. Using a small insulated screwdriver adjust this potentiometer clockwise to speed up and counter-clockwise to slow down the max speed of the treadmill. A tiny turn of this potentiometer will make a big difference in speed so be careful when making adjustments. It is not important to get the speed set exactly at the max speed of the treadmill but do make sure to get the speed within.2 MPH of the max speed of the treadmill.

For instance if the max speed of the treadmill is 10 MPH, make sure to have the speed set between 9.8 MPH and 10.2 MPH. Some models have a 12 MPH top speed, so please check your manual if you aren’t sure. After completing calibration of the speed, press the Speed Down key. The treadmill will automatically return to 0 MPH. Please allow the unit to stop completely before continuing.

Press the Stop key once and remove the safety key. Jun 11, 2010 . E21or E2 1 means the treadmill is not picking up a speed signal once the start key is pressed. First, determine if the motor is turning before you get the E2 1 or not.

If the motor turns, the speed sensor is the most likely problem. If it does not, you can manually turn the belt with your feet before you get the E2 1 and you should get a speed reading but eventually you will get an error code because it is almost impossible to keep the speed constant enough for the computer.

Try running it through calibration with the motor cover removed. Their is Tech sheet under the hood and it will explain how to do the calibration May 22, 2010 .